Description
The INSTEON DIN-Rail Relay (On/Off) clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or any other INSTEON Controller for full remote control over the module and it’s connected load.
- Simply clip onto 35mm DIN rail and wire like any other INSTEON inline module
- Optional sense wires allow for control via a connected, hard-wired switch
- Compatible with latching, single-momentary and dual-momentary switches
- Award-winning INSTEON technology provides superior reliability
- This product should be installed by a licensed electrician
Easy DIN rail installation
When planning the electrical wiring for your home or business, avoid adding too many wall switches in a single location. Wall switches ganged together cause homeowner confusion and can quickly ruin the aesthetic of a room. Instead consider adding a single INSTEON controller to control all the lighting. It’s easy when combined with INSTEON DIN-Rail products.
Please note that this product must be installed by a licensed contractor.
How it works
The DIN-Rail Relay (On/Off) module clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or any other INSTEON device for full remote control over the module and it’s connected load. Specifically, DIN-Rail Relay is compatible with the “Top hat rail EN 50022” (sometimes referred to as a Type O or Type _) The DIN Rail On/Off will fit either variation of this style DIN rail (either 15 or 7.5 mm “high” off the mounting surface).
What is a DIN rail?
It is simply a metal rail on which compatible products (circuit breakers, switches, etc.) can be snapped on. The DIN rail can simply be mounted to any flat surface (or even across studs). Please follow all applicable building and electrical codes whenever installing electrical products.
Cross section
With module clipped on 
General |
|
| Product Name: | INSTEON DIN-Rail Relay (On/Off) |
| Product Code: | 2453-522 |
| Regions: | Australia and New Zealand |
| In the box: | INSTEON DIN-Rail Relay (On/Off) |
| Warranty: | 2 Years |
INSTEON |
|
| INSTEON: | Controller and responder |
| Maximum links/scenes: | 400 |
| Status LED: | Green when load is on, red when load is off, Blinks green or red during setup, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software) |
| LED brightness: | Adjustable from off to 100% bright |
| Local control: | Yes |
| Commands supported as controller: | On /?Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim |
| Commands supported as responder: | On / Off, Fast on / Fast off, Beep |
| Software configurable: | Yes |
| RF range: | 45m |
| Phase detect beacon: | Yes |
| X10 support: | Yes |
| X10 addresses: | Any 1 of 256 (unassigned by default) |
| INSTEON device category: | 0x02 switched lighting control (all frequencies) |
| INSTEON device subcategory: | 2453-222 (921MHz), 0x2E |
Operational |
|
| Status LED: | Green. Blinks on activation |
| Sense Modes: | Jumper Installed: Open = Group 1 On, Closed = Group 1 Off; Jumper Uninstalled: Open = Group 1 On (or off), Closed = Group 2 On (or Off) |
| Aux. Sensor Input: | Senses contact closure |
| Aux. Sensor Input Wire: | >= 20 gauge wire |
| Setup Memory: | Non-volatile EEPROM |
Mechanical |
|
| Mounting: | 35mm (top hat) DIN rail |
| Max. cable size: | 4mm?, 12 AWG (2.72mm diameter) |
| Min. cable size: | 1.5mm?, 15 AWG |
| Screw DIN rail connections: | Line, Neutral, Load, Sense 1, Sense 2 |
| Casing: | UV stabalized plastic (INSTEON White) |
| Set button: | Yes |
| Beeper: | Yes |
| Beep on button press: | Optional (off by default) |
| LED: | 1 RGB |
| Dimensions: | 80mm W x 53mm H x 63mm D |
| Weight: | 175g |
| Operating Conditions: | Indoors, 0? C to 40? F, up to 85% relative humidity |
Electrical |
|
| Voltage: | 100VAC to 240VAC |
| Frequency: | 50/60Hz auto-detected at power-up |
| Max. load: | 15A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs/low voltage halogen |
| Load types: | Resistive, Inductive/capacitive, Low voltage halogen |
| User replaceable fuse: | Yes (16 A (T)) 5x20mm fuse |
| Retain all settings without power: | Yes, saved in non-volatile EEPROM |
| Standby power consumption: | <1W |
| Certification: | Approved for use in Australia and New Zealand |
