‭02 8970 8767‬ sales@hancan.com.au

INSTEON DIN-Rail Dimmer

$99.00 inc. GST

The INSTEON DIN-Rail Dimmer module clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or any other INSTEON device for full remote control over the module and it’s connected load. Specifically, DIN-Rail Dimmer is compatible with the “Top hat rail EN 50022” (sometimes referred to as a Type O or Type _) The DIN Rail Dimmer will fit either variation of this style DIN rail (either 15 or 7.5 mm “high” off the mounting surface).

In stock

SKU: HANCAN-NDL-IN2452-522 Category: Tag:

Description

The INSTEON DIN-Rail Dimmer clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or other INSTEON Controller for full remote control over the module and it’s connected load.

  • Simply clip onto 35mm DIN rail and wire like any other INSTEON Controller
  • Optional sense wires allow for control via a connected, hard-wired switch
  • Compatible with latching, single-momentary and dual-momentary switches
  • Award-winning INSTEON technology provides superior reliability
  • This product should be installed by a licensed electrician

Easy DIN rail installation

When planning the electrical wiring for your home or business, avoid adding too many wall switches in a single location. Wall switches ganged together cause homeowner confusion and can quickly ruin the aesthetic of a room. Instead consider adding a single INSTEON controller to control all the lighting. It’s easy when combined with INSTEON DIN-Rail products.

Please note that this product must be installed by a licensed contractor.

How it works

The DIN-Rail Relay (On/Off) module clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON keypad or any other INSTEON device for full remote control over the module and it’s connected load. Specifically, DIN-Rail Relay is compatible with the “Top hat rail EN 50022” (sometimes referred to as a Type O or Type _) The DIN Rail On/Off will fit either variation of this style DIN rail (either 15 or 7.5 mm “high” off the mounting surface).

What is a DIN rail?

It is simply a metal rail on which compatible products (circuit breakers, switches, etc.) can be snapped on. The DIN rail can simply be mounted to any flat surface (or even across studs). Please follow all applicable building and electrical codes whenever installing electrical products.

Top hat DIN rail

Cross section

With module clipped on

Specifications

General

Product Name: INSTEON DIN-Rail Dimmer
Product Code: 2452-522
Regions: Australia and New Zealand
In the box: INSTEON DIN-Rail Dimmer
Warranty: 2 Years

INSTEON

INSTEON: Controller and responder
Maximum links/scenes: 400
Load brightness levels: 32 locally (256 with software)
Status LED: Green when load is on, red when load is off, Blinks green or red during setup, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software)
LED brightness: Adjustable from off to 100% bright
Local ramp rate: Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 8 minutes with software)
Local control: Yes
Commands supported as controller: On /?Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim
Commands supported as responder: On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim, Incremental brighten / Incremental dim, Beep
Software configurable: Yes
RF range: 45m
Phase detect beacon: Yes
X10 support: Yes
X10 addresses: Any 1 of 256 (unassigned by default)
INSTEON device category: 0x01 dimmable lighting control
INSTEON device subcategory: 2453-222 (921MHz), 0x34

Operation

Status LED: Green. Blinks on activation
Sense Modes: Jumper Installed: Open = Group 1 On, Closed = Group 1 Off; Jumper Uninstalled: Open = Group 1 On (or off), Closed = Group 2 On (or Off)
Aux. Sensor Input: Senses contact closure
Aux. Sensor Input Wire: >= 20 gauge wire
Setup Memory: Non-volatile EEPROM

Mechanical

Mounting: 35mm (top hat) DIN rail
Max. cable size: 4mm?, 12 AWG (2.72mm diameter)
Min. cable size: 1.5mm?, 15 AWG
Screw DIN rail connections: Line, Neutral, Load, Sense 1, Sense 2
Casing: UV stabalized plastic (INSTEON White)
Set button: Yes
Beeper: Yes
Beep on button press: Optional (off by default)
LED: 1 RGB
Dimensions: 80mm W x 53mm H x 63mm D
Weight: 175g
Operating Conditions: Indoors, 0? C to 40? F, up to 85% relative humidity

Electrical

Voltage: 100VAC to 240VAC
Frequency: 50/60Hz auto-detected at power-up
Max. load: 300W at 100-240VAC
Load types: Incandescent
User replaceable fuse: Yes (16 A (T)) 5x20mm fuse
Retain all settings without power: Yes, saved in non-volatile EEPROM
Standby power consumption: <1W
Certification: Approved for use in Australia and New Zealand