‭02 8970 8767‬ sales@hancan.com.au

FIBARO Z-Wave Double Switch 2

$119.00 inc. GST

The remotely operated FIBARO Double Switch 2 is designed to turn two electrical devices on and off and to measure their power and energy consumption. The compact size of the device makes it the world's smallest of its type and allows for the product to be installed in wall switch boxes or housings. FIBARO Double Switch 2 can be controlled either via Z-Wave network or with a wall switch through a direct connection.

In stock (can be backordered)

SKU: HANCAN-DHS-LIT-SWW-FIB-022 Category: Tags: ,


The new?Fibaro Z-Wave Double Switch 2?(FIBEFGS-223) is a smart Z-Wave wireless module which can control two circuits each with a maximum load of 6.5A per channel and 10A total load per circuit.

  • Control the ON-OFF function of two two independent circuits or appliances remotely or using a wall switch
  • Compatible with all Z-Wave networks
  • Acts as a repeater expanding your Z-Wave network
  • Wide range of compatibility with existing light fittings and does NOT require expensive cabling
  • Latest generation Z-Wave 500 series chip
  • Z-Wave Plus certification
  • Very accurate energy measurement /- 1 % for power above 5W
  • Supports secure mode (Z-Wave Network Security) encrypted with AES-128
  • No dry contacts?– this is important. It means that the new FGS-223 cannot be used to control low voltage systems such as garden lights and irrigation, or where you want a pure volt-free switch such as alarm panels and garage door controls. If you need device with dry contacts please see?zConnect Z-Wave Garage Door Opener?or FIBARO Z-Wave Single Switch InWall?or DHS Z-Wave Single Switch InWall

Product Details

The?Fibaro Z-Wave Double Switch 2?(FIBEFGS-223) is a smart Z-Wave controller capable of remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.

The device is designed to operate inside your wall socket and can be easily installed by a qualified electrician.

This?Fibaro Z-Wave Double Switch 2?requires 3-wire (including neutral) installation and works with an AC (230V) power supply.

The?Fibaro Z-Wave Double Switch 2?also features a secondary switch input which allows it to directly control other associated Z-Wave devices. This means that by turning the switch ON/OFF you can also turn other associated devices ON/OFF even if they are not physically connected to the same Fibaro module. It also enables you to control the local load as part of 2-way and multi-way lighting circuits.

This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:

  • Raspberry PI with RaZberry Card
  • Fibaro Home Controller 2/Lite
  • DHS Z-Wave Universal Remote Controller
  • DHS Z-Wave Mini Remote Controller

Please check the maximum load before installing or operating.

This installation must be done by a certified electrician in Australia and New Zealand.

Before engaging an electrician, check that they provide an electrical compliance certificate.

For warranty claim you have to provide installation compliance certificate from your electrician.

Product Support


Fibaro Z-Wave Single Switch 2 Manual (Size: 724 Kb)

Videos / YouTube:

Fibaro Home Center 2 Presentation

Fibaro Energy monitoring

Technical Specifications

RF Protocol
RF Frequency
921.42MHz AU/NZ Approved RF for Z-Wave
Z-Wave device type
Z-Wave Switch, Routing Slave
230V 10% 50/60 Hz
Operation Range
Up to 20 m indoors with no obstacles
Indoor use only, up to 1.5kW resistive load per circuit
Operation temperature
0 ~ 55?C
Storage temperature
10 ~ 80?C
EN 55015, EN 60669-2-1

Regulatory Compliance Mark



(LxWxH) 42mm x 37mm x 17mm

Installation Instructions and more on Fibaro Manuals Support Page.

Additional information